Ericsson 1553-FGC 101 1010 Uen A Podręcznik Użytkownika Strona 129
- Strona / 196
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Code Upgrade and License Key Entry
7.1 Introduction
This chapter specifies the procedure for upgrading software via FTP and obtaining
and entering license keys to enable DVBCA, Authentication, 1GHz RF or M-CMTS
functionality on the EQ8096.
The assembly is referred to as the unit in this document.
7.2 How to Install Software
7.2.1 Read This First!
Caution!
Upgrading a product will interrupt its normal operation. Code can be loaded at any
time without interfering with the unit functionality. However, for the new code to be
activated a power cycle is required. Ensure that the unit is not in use at this time.
Before starting, ensure that the programming procedure is well understood.
7.2.2 If the IP Address is Not Known
The unit IP (Main) address can be obtained from the Front Panel LCD; alternatively
the user can access the serial port by connecting to a PC running HyperTerminal
with the following settings:
• 115200 baud
• 8 data bits
• 1 stop bit
• no parity
• no flow control
To establish the unit IP address connect the serial port as above, power on the unit
and the IP address settings will be displayed as part of the boot sequence.
Alternatively to display all the control port settings, at the Monitor> prompt type:
Monitor> ipinfo
To set a new IP address type Monitor> IP3 xxx.xxx.xxx.xxx
To set a subnet mask (if required) type Monitor> IPMASK3 xxx.xxx.xxx.xxx
To set a default gateway (if required) type Monitor> IPGATEWAY xxx.xxx.xxx.xxx
2/1553-FGC 101 1019 Uen A
7-3
- EQ8096 Universal Edge QAM 1
- Introduction 4
- Revision History 4
- Associated Documents 4
- Trademarks 4
- Warnings, Cautions and Notes 5
- EMC Compliance 6
- Contact Information 6
- Preliminary Pages 7
- Preliminary Pages 8
- 1 Introduction to the EQ8096 9
- Introduction to the EQ8096 10
- 2/1553-FGC 101 1019 Uen A 10
- Caution! 11
- Warning! 11
- 1.2 Summary of Features 13
- 1.2.2 Data Input 14
- Introduction to the EQ8096 15
- 1.3 Output Channel Mappings 16
- 1.3.2 UDP Port Mapping 18
- 1.4 Guided Tour 19
- 1.4.3 Front Panel Controls 20
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Introduction 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 29
- 2.5 -48 V DC Power Supply 31
- 2.5.3 DC Connector Details 33
- 2.6 Signal Connections 34
- 2.6.4 Control 36
- 2.6.7 ASI Monitor port 36
- 2.6.8 Host Status 36
- 2.7 Indicators 37
- 2.7.2 Rear Panel 38
- Chapter 3 39
- 3.1 Introduction 43
- 3.3 Web Page Menus 45
- 3.3.3 Data Port Settings 50
- 3.3.4 Modulation Settings 52
- 3.4.4 Broadcast Mode 61
- 3.4.5 DEPI/M-CMTS Mode 67
- 3.5.1 Overview 67
- 3.5.2 CA ECMG Settings 68
- 3.5.3 CA Settings 69
- 3.6 Engineering Tabbed Page 70
- 4 Alarms 75
- Alarms 76
- 4.1 Introduction 77
- 4.2 View Active Alarm Table 78
- 4.3 Configure Active Alarms 78
- 4.4 Specific Alarms 79
- 4.4.5 Temperature Alarms 81
- 4.5 Trap Destination Table 82
- 4.6 Status Indicators 83
- 4.7 Unit Alarm List 84
- Alarms 85
- Using XML File Download 97
- 5.1 Introduction 99
- 5.2 FTP File Transfer 99
- 5.3 XML Files 99
- 5.3.1 XML File Format 100
- 5.3.2 Status File Examples 100
- 2/1553-FGC 101 1019 Uen A 101
- 5.4.1 EMM Connections 105
- 5.4.4 Multiple EMM Streams 108
- 5.4.7 Stopping Encryption 110
- 5.4.8 Simulcrypt 111
- 5.5 Errors during FTP 113
- 5.8 Redundancy Switch 116
- Chapter 6 117
- Contents 117
- 6.1 Introduction 119
- 6.2 Preventive Maintenance 119
- 6.3 Alarms 120
- 6.4 Fault-finding 121
- 6.5 Power Supply Problems 123
- Chapter 7 127
- 7.1 Introduction 129
- 7.2 How to Install Software 129
- 7.4 Requesting a Key 130
- Information’ tab 132
- 8 Unit Configuration via FTP 133
- Unit Configuration via FTP 134
- 8.1 Introduction 135
- Output Option Cards 137
- 9.1 Introduction 139
- 9.3.1 Preparing the Unit 143
- 9.3.5 Reconfigure the Unit 145
- Specification 147
- 10.1 General 149
- 10.3.1 System Setup 151
- 10.3.2 M-CMTS Session Setup 151
- 10.3.4 DTI Card 157
- A Glossary 159
- Glossary 160
- Glossary 161
- B Technical Specification 179
- Technical Specification 180
- B.1 Unit Specification 181
- B.2 Rear Panel Connectors 182
- B.2.3 RF Output 183
- Parameter Requirement 184
- B.2.5 Ethernet Control 185
- Technical Specification 187
- B.3 Power Supply 188
- B.4 Physical Details 189
- B.6 Compliance 190
- B.6.3 Telecommunications 191
- B.6.4 CE Marking 191
- B.6.5 C-Tick Mark 191
- B.6.6 Packaging Statement 192
- B.6.7 Packaging Markings 192
- B.6.9 Equipment Disposal 194
- B.6.10 Recycling 194
- B.7 Cable Types 195
Powiązane produkty i podręczniki dla Odbiornik Ericsson 1553-FGC 101 1010 Uen A
Odbiornik Ericsson RX8000 Series Dokumentacja
(37 strony)
(37 strony)
Odbiornik Ericsson RX8000 Series Dokumentacja
(26 strony)
(26 strony)
Odbiornik Ericsson RX8330 Dokumentacja
(39 strony)
(39 strony)
Odbiornik Ericsson TT1222 Podręcznik Użytkownika
(198 strony)
(198 strony)
Odbiornik Ericsson LBI-38505A Instrukcja Użytkownika
(197 strony)
(197 strony)
Odbiornik Ericsson TT1222 Podręcznik Użytkownika
(20 strony)
(20 strony)
Odbiornik Ericsson RX8315 Podręcznik Użytkownika
(40 strony)
(40 strony)
Odbiornik Ericsson RX8200 Podręcznik Użytkownika
(44 strony)
(44 strony)
Odbiornik Ericsson RX8315 Podręcznik Użytkownika
(24 strony)
(24 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji